Atlantic Water Solutions of Alfred, Maine

Expert Well Drilling in Maine and New Hampshire

Water Well Drilling 

Well drilling can be done to extract natural resources out of the ground such as water, natural gas or petroleum.

1. CHECK VALVE
(Section G) Located at the top of the pump, it prevents backflow into the pump and holds the head of water in the system.
2. BRASS ROPE ADAPTER
(Section A) Connects the Pitless Adapter and the Submersible Pump with Safety Rope.
3. IDEAL CLAMPS
(Section Q) All-stainless steel clamps for dependable connections between Pipe and Insert Fittings or Torque Arrestor.
4. 3M™ HEAT SHRINK SPLICE KIT
(Section S) For waterproof electric cable splices in submersible pump installations.
5. TORQUE ARRESTOR
(Section R) Installed directly above Submersible Pumps to protect pump and well components from starting torque damage.
6. SAFETY ROPE
(Section R) A safety line from the top of the well to the pump.
7. CABLE TIE
(Section R) Fastens Cable to Drop Pipe
8. CABLE GUARD
(Section R) U.S. Patent #6,595,284 Protects submersible cable wires from abrading against sides of well. Two styles available: SelfClamping or Snap-in.
9. PITLESS ADAPTER
(Section M) Provides a watertight, sanitary, removable connection between the pump and the house. Installed in casing below the frost
line to prevent freezing.
10. BRASS INSERT FITTING
(Section A) Provides connection between poly pipe and pipe thread of Pitless Adapter.
11. WATERTIGHT WELL CAP
(Section L) Inner gasket compresses to outside diameter of casing to provide a watertight seal. Top of cap removes easily to access
well for service.
12. WELL SEAL
(Section K) Used in above-ground installations to provide a positive seal inside casing.
13. CHECK VALVE
(Section G) On pump installations, a Check Valve installed near the tank inlet holds water in the tank when the pump is idle.
14. TANK TEE
(Section O) Connects water line from pump to pressure tank and service line from tank to house. Taps are provided to accept Pressure
Switch, Pressure Gauge, Drain Valve, Relief Valve, Snifter Valve, etc.
15. DRAIN VALVE
(Section H) For easy draining of the system.
16. BRASS NIPPLE
(Section D) Male threads allow attachment of Pressure Switch to Tank Tee.
17. RELIEF VALVE
(Section I) Protects against pressure build-up. Should be used on any system where the pump could develop greater pressure than the
maximum rating of the system.
18. PRESSURE GAUGE
(Section R) Measures water pressure in Pressure Tank.
19. PRESSURE SWITCH
(Section S) Signals the pump to start when the water system drops to a preset low pressure, and to stop when the high pressure mark
is reached.
20. SQUARE D SAFETY SWITCH
(Section S) For electric control and distribution to the pump.
21. LIGHTNING ARRESTOR
(Section S) Protects pump motor & controls from voltage surges caused by lightning, switching loads, and power line interference.
22. BALL VALVE
(Section H) Acts as a shutoff valve on the supply line from the tank to the house.
23. WATER FILTER
(Section T) A point-of-entry, whole-house-filter that removes rust particles, sand, etc. from supply water.

 

Well Drilling Well Drilling Diagram Atlantic Water Solutions

 

Atlantic Water Solutions LLC

 

PO BOX 602, Alfred, Maine 04002
Email: cindy@atlanticwatersolutions.com
Phone: 800-696-9355

 

Social Networks

 

Atlantic Water Solutions Alfred, Maine Facebook   Atlantic Water Solutions Alfred, Maine Twitter 5 Star Customer Reviews of Atlantic Water Solutions Alfred Maine

Associations

Water Quality Association Maine

Maine Groundwater Association

Screened HomeAdvisor Pro - Atlantic Water Solutions, LLC
Atlantic Water Solutions BBB Business Review

Atlantic Water Solutions LLC
PO BOX 602, Alfred, Maine 04002
Email: cindy@atlanticwatersolutions.com

Social Networks

Associations

 Water Quality Member      maine

 

Atlantic Water Solutions BBB Business Review

Contact us for more information.

Pumps Wells Water Treatment Filtration Other

© 2018 Atlantic Water Solutions